A 3mm suit with back and shoulder reinforcements for greater comfort when wearing a diving tankâ€”perfect for intermediate male divers in warm waters. 3mm wetsuit with back and shoulder reinforcements for greater comfort when wearing a diving tank! Diving wetsuit for warm waters. Comfortable. Easy to get on.
3 mm full wetsuit, watertight seams (GBS) and smooth cuffs.
Shoulder and lower back reinforcements for more comfort when carrying a tank.
One-piece wetsuit with back zip fastener.
Freedom of movement
Stretch neoprene and fitted cut with no underarm seams.
Ergonomic reinforcements on the knees.
DIVING DIVING SCUBA DIVING
LEVEL OF PRACTICE
3 mm full one-piece wet type with back zip. Seams taped using a GBS (glued and blind stitched) assembly. Once a thin layer of water (that enters through the zip) gets trapped between your body and the wetsuit, the water stays warm as it is not replaced. This thin layer of water keeps you warm. Rolled, smooth edged cuffs, ankles and neck for maximum watertightness.
The seams of the wetsuit are waterproof, with a GBS assembly (Glued and Blind Stitched): the neoprene is glued and then stitched for maximum resistance (the needle does not go all the way through the neoprene to prevent water getting through).
A wetsuit specially developed for greater comfort when carrying a diving tank and wearing a buoyancy compensator. The neoprene reinforcements are strategically positioned at the points of the BC exposed to pressure. 5mm more neoprene on the shoulders, the collar bones and the lumbar zone that acts like a cushion. Snap hook on the upper thigh to attach accessories.
One-piece with stretch neoprene side panels (very soft and stretchy neoprene) to adapt to fit different body shapes and suit various physiques. The extremities of the legs and arms are also made of stretch neoprene for easier dressing. No underarm seams for easier arm movements.
The wetsuit is equipped with reinforcements on the knees to increase resistance. There are also prints on the friction zones linked to the buoyancy compensator (shoulders and lower back). Also provides better body support and prevents the BC from slipping on the slides.
Even in warm waters, the body ends up cooling down (25 times faster than in the air). Use a thin 3 mm wetsuit that will allow you to delay this drop in temperature so that you can enjoy your activity for longer. In addition, use a full wetsuit to fully protect you from UV rays and the underwater environment (coral, etc.).
This scuba diving suit provides thermal protection that has been tested by the independent INPP institute (Marseille, France) in order to validate its compliance with the current standard (EN 14225-1:2017). This wetsuit is certified for use in waters warmer than 25Â°C.
This is the most common type of diving suit on the market. It is not designed to keep the water out, but to trap it, so that your body then warms it up, creating a thermal buffer between you and the outside. Made of neoprene - a rubber polymer filled with air bubbles - these wetsuits are available in thicknesses of 0.5 to 7 mm. Thanks to their suppleness and modularity, they make excellent diving wetsuits.
Put your foot in a plastic bag. Then put your leg into your wetsuit. Your foot comes out completely and smoothly! To adjust, ask someone to blow into your sleeve from the wrist. The incoming air inflates the interior of the neoprene wetsuit, immediately separating it from your skin. You can then easily proceed with the final adjustments.
1) Soak the inside and the outside of the wetsuit in clean water after each session. 2) Clean with a bactericide solution. 3) Rinse thoroughly in clean water. 4) Dry on a wide hanger in a dark and well ventilated place. Pay attention to the sun, because it will cause the textile parts of the wetsuit to fade. Zip fasteners can be cleaned with a toothbrush and lubricated with a suitable lubricant, such as silicone grease.
Dry your wetsuit out of the sun and well clear of all sources of heat. Store your wetsuit on a hanger to keep its shape and conserve the neoprene.
Designed and tested by our teams and our technical partner in Hendaye (France) to approve the thermal insulation.