Designed and developed in the French Alps, this 1-2 person 3 seasons trekking tunnel tent is ultra lightweight and compact with minimalist comfort. With its extremely compact tunnel structure, it offers a small, essential living space: 2 doors, only 1 porch, 2 pockets. Poles in sleeves for quick pitching and dismantling.
Total weight 1.75 kg Compact & compressible bag 5 L Dimensions 39 x 12 x 11 cm
60 cm width per person Bedroom height 95 cm 2 doors. 1 porch. 2 pockets.
Resists 70 km/h winds (force 8): validated in wind tunnels on rotating plate.
Easy assembly / dismantling
Quick pitching: pre-assembled room and flysheet. Sleeves for the tent poles.
Water column (Schmerber): Flysheet > 2000 mm. Bedroom groundsheet > 3,000 mm.
Flysheet. 2 vents for air flow.Room with mosquito nets.
Total weight 1.75 kg Separable parts to help transportation. Flysheet alone 730g Room only 542 g Pole kit 206g Pegs (11 pieces) 110g Bags 57g + 10g Guy ropes (4 pieces) 20g Repair kit (ferrules, patch) 20g
To protect your product and increase protection from the ground and bad weather, you can accessorise your Trek 900 UL 2P tent with a survival blanket-type groundsheet.
Weights, volumes & dimensions may vary slightly due to production tolerances.
Size and living space
Bedroom length 205 cm Bedroom width 110 cm to the head, 130 cm to the shoulders and 80 cm to the feet. Height of the bedroom 95 cm Extensions (integrated poles, 1 part) at the 4 corners to increase useful volume inside the tent. 60 m wide (at widest point) porch provides storage space that doesn't obstruct bedroom entrance. Store two 50 litre backpacks maximum. 1 side pocket to store possessions.
Architecture, tent poles and tent pegs
Lightweight, shock and frost resistant aluminium pole: 7001 T6 Yunan SD70PF Ø 9 mm aluminium. Optimised square tent pegs: “anvil” head, oversized main part, extremely resistant and lightweight (7075 T6 aluminium). Non-anodised for a lower environmental impact.
The single pole and 4 integrated parts form a non self-standing tunnel. This structure forms a very light tent that needs to be fixed to the ground and does not stay up alone.
Extremely quick pitching/striking. The flysheet and bedroom are pre-assembled. Insert the tent poles into the flysheet cover. It is also quick to strike. To store the tent in its bag, fold the tent in half to about the length of the bag, fold up the pole into a bundle onto the bedroom or flysheet, roll everything up tightly to slide into the bag.
Forclaz tents are laboratory-tested: pitched tent, 200 litres/sqm/hour (3 hours, equivalent to a tropical storm). They are also tested in the field by a sample user group. 20 denier polyester (PES) flysheet and 40D polyamide (PA) groundsheet have a polyurethane coating (inside) and silicone (exterior). Seams taped with heat-sealed strips. Multi-component bedroom combining breathability, wind protection and prevents condensation
We test all our tents in a wind tunnel on a turntable where we can expose each side of the tent to the wind. To test its wind resistance, the tent must be properly pitched, taut but not stretched, with all the guy ropes in position around the tent. It should remain habitable at wind speeds of 70km/h, measured near ground level. Our tents are certified by the CSTB independent laboratory in Nantes.
Ventilation and condensation prevention
Bedroom with mosquito screen for ventilation and water-repellent fabric to protect from condensation and draughts. Large vent at front of tent and additional vent at feet end. To reduce condensation inside your tent, it must be properly pitched, with the fabric kept taut without being over-stretched. Vents and good air flow will help reduce humidity inside your tent.
3-season tent: your tent will protect you from the harsh weather conditions you can encounter in the spring, summer or autumn. It will withstand light snowfall but is not designed to withstand heavy loads that would weigh on the structure. In case of snow, remember to shake your tent regularly in order to bring down any snow that has accumulated to avoid putting too much weight on the structure of your tent.
The poles are coloured using an innovative anodising method which eliminates the use of nitric and phosphoric acids. Non-anodised tent pegs: Your tent pegs may have a “rough” or “used” appearance but they still have all their technical and resistant features; not coloured or anodised (no acid is used since this only has an aesthetic effect). These actions help to reduce the environmental impact of your product.
Repairs and After-sales service
As designers and users who love our playing field, we care about the durability of our products, that’s why all our tents are designed to be repairable. You will find the detachable parts (poles, bedroom, etc.) in store or in the workshop of your local Decathlon, or on the website. If you have a problem, don't hesitate to have your tent looked at in your local Decathlon store. Repair kit (ferrule, patch): 20 g
Your tent is designed for itinerant bivouacking, it is therefore not designed for static use in the sun. We recommend that you avoid leaving it in the sun as the ultra-light fabrics can be sensitive to UV light, that damages them.
MAINTENANCE OF PRODUCT
Do not wash
Do not bleach
Do not tumble dry
Do not iron
Do not dry-clean
Main fabric: 20.0% Thermoplastic Polyurethane, 80.0% Polyester